Datasheet: Emax Es08ma Ii

void loop() // Read the potentiometer value (0 to 1023) int sensorValue = analogRead(potPin); // Map the 0-1023 value to a 0-180 degree angle angle = map(sensorValue, 0, 1023, 0, 180); // Move the servo to the calculated angle myServo.write(angle); delay(15); // Short delay for smooth movement

The EMAX ES08MA II is a high-performance brushless motor designed for RC enthusiasts and drone enthusiasts. As a popular choice among hobbyists, it's essential to dive into the datasheet to understand its capabilities, features, and applications. In this blog post, we'll provide an in-depth analysis of the EMAX ES08MA II datasheet, covering its specifications, characteristics, and more.

The ES08MA II is fully compatible with the standard Servo.h library included in the Arduino IDE.

The following technical details are sourced from the official Mini SERVO (ES08MAII) SERIES datasheet : Specification @ 4.8V Specification @ 6.0V Stall Torque 1.6 Kgf·cm (21.0 oz·in) 2.0 Kgf·cm (28.0 oz·in) Operating Speed 0.12 sec/60° (at no load) 0.10 sec/60° (at no load) Operating Voltage 4.8V – 6.0V DC 4.8V – 6.0V DC Operating Current Dimensions 23 x 11.5 x 24 mm (approx. 1.25 x 0.45 x 0.94 in) Weight 12 g (0.42 oz) Gear Material Full Metal Plug Type Futaba / JR (Universal) Direction Counter-Clockwise (1500 to 1900 µsec) Helpful Applications and Use Cases Emax Es08ma Ii Datasheet

servo serves as a primary upgrade over standard plastic-geared 9g servos.

The EMAX ES08MA II Go to product viewer dialog for this item.

| Model | Torque @6V | Speed @6V | Weight | Bearings | Price Range | |-------|------------|-----------|--------|----------|--------------| | | 2.0 kg·cm | 0.10 sec | 12.5g | Dual | $ | | TowerPro MG90S | 2.2 kg·cm | 0.11 sec | 13.4g | Single | $ | | Hitec HS-65MG | 1.9 kg·cm | 0.12 sec | 11.2g | Dual | $$$ | | Savöx SH-0255MG | 2.5 kg·cm | 0.09 sec | 12.9g | Dual | $$$$ | void loop() // Read the potentiometer value (0

Note: While I cannot link directly to a PDF, this write-up contains the critical information found in the official datasheet.

The ES08MA II’s mechanical stops allow approximately 200° of total travel, but the linear control range is 180° (1000-2000 μs). Do not send pulses below 800 μs or above 2200 μs to avoid damaging the internal potentiometer.

is a high-torque micro servo designed for applications requiring a balance of small form factor and mechanical durability. Unlike standard nylon-geared servos, this model features , significantly increasing its lifespan and resistance to impact or high-load stresses. 2. Mechanical Characteristics Dimensions: ) [ 0.5.2 ]. Weight: (including wire and connector) [0.5.2]. Gear Material: All Metal. The ES08MA II is fully compatible with the standard Servo

The following data outlines the operational parameters of the EMAX ES08MA II under standard conditions. EMAX ES08MA II 12G analog servo drive with metal gearbox

3D flight in foam airplanes, gliders, and small fixed-wing models. ReadyMadeRC Mini SERVO (ES08MAII) SERIES

Receives control pulses from a microcontroller or RC receiver.